https://edgilkisonvelocette.blogspot.com/2024/03/bob-strode-and-his-track-bike-he-built.html
https://edgilkisonvelocette.blogspot.com/2024/03/velocetteer-bob-strode-has-passed-away.html
![]() |
Once the fork assembly is ready, it's time to begin the fitting into the triple clamp setup. The spacer/spring holder might be a very tight fit into the lower triple clamp. With a wedge expanding the pinch opening I used a brake hone to clean up the surface and make it slightly wider. On the spring holder Ed G. suggested to use a file and lightly reduce it's diameter. Since it wasn't too far off I used the interference marks as an indicator as to where to file.
Ray said he would be down at the shop after his Worcester trip. So I packed up all the bits, solder, flux and gloves to head to toy shop east. Ray was in the back with a couple of old timers. The torch was ready by the bench vise, I just set right to it. First step was to give it a quick rub with emery cloth both the outside of the tube and inside of the casting. Next step was to use a brush to apply the flux before an initial tinning of the components.
It's funny how the bike gods work sometimes. When I left the workshop last night I was pondering how to approach the solder joint repair to the fork legs. The little propane bottle was melting the solder but just missing out on the heat and then the question of how to grip the tube... Ok, I'll sleep on it.
After morning coffee, in came the mail and with it the latest Fishtail. Wouldn't ya know- they had a write up on the process of re-soldering fork tubes. Well it seems that yes, I was not using enough heat. That and an added trick of twisting the tube as the solder melted. So I gave Ray B. a call at 'Toy shop East' to see what he might have on hand. The 'Toy shop' as it is, is an old chassis/speed shop with all manners of equipment for causing great mayhem. Ray bought the shop a few years ago. It's the same shop that I would buy sheet steel for my 440 Datsun project in my youth [ https://newenglandzen.blogspot.com/2010/12/datsun-1200-with-440-or-youthful-folly.html ] the same shop that built Jungle Jim's Vega back in the day. I find it comforting that I can go to places like this and be at home as it were, just a good feeling of living nostalgia.
Ray was in, so I was on my way. We talked about it for a few minutes; the process, the technical aspects and all involved. As we talked, tools came out and we gave it a go. Putting the axle lug in the vise and a section of flat stock across the top so as to have it catch on the springs tab retainers, I put Ray's larger propane heater to it. After not too long I gave a slight twist to the flat stock and heard a slight squeak in the joint. With a couple more twisting actions the whole unit loosen up and was able to be pulled clear of the casting! Excellent, we had success in making many from one!
So now what? Well, on to finding a few tools, gathering the proper flux and solder, give it all a good cleanup and put it back together. I'm just excited that it came apart as well as it did.It was a little difficult jumping back into the Thruxton, I hadn't made up my mind what to do about the front tire. Rather than take the front wheel on and off several times, I thought to make it all into one go around. The right side clip on was cracked meaning that either the triple clamp needed to be removed or the fork tube would need to be dropped. The wheel and fender need to be removed if one wants to install the lower fairing section as well. As for a tire, currently the selection out there is somewhat thin. I'd like to stick with an Avon speedmaster MkII or Dunlop K model; I'm not finding much...
But then there was the drip...
At first you get hopeful, a spot of oil on the floor could have come from anywhere. Wipe it up and hope for the best. Just keep an eye on things over time. Maybe a loose crush washer, maybe a loose nut on the bottom of the fork leg. There was silicone sealant on the bottom of the fork tube, but I knew better. It was more likely crash damage to the slider. Velocette sliders are made of three parts; the upper bushing/seal and spring holder, the lower casting to hold the axle and a section of tubing between the two. All of these components are soldered together and one of the reasons NOT to powder coat the legs as the ovens used in the powder coating process will melt the solder.